Adding a room or a workshop and need the floor poured? We prep the ground, set the steel and finish a slab for your flooring.
Concrete floor installation in Calabasas means we form, pour, place and finish the slab that becomes the floor of a room, an addition, a garage conversion or a workshop. It's what the trade calls flatwork, the same family of jobs as patios, driveways and sidewalks, and the slab is only as good as the ground and steel under it.
The price mostly comes down to the size of the floor, how much digging and base work the ground needs, whether plumbing or electrical runs under the slab, which reinforcement goes inside it and how easily our crew can get concrete to the spot. The schedule depends on the city's permit and inspection steps and on the wait for the slab to dry before your flooring goes down, and the estimate I write up after seeing the site is where you get your own number.
When a budget gets tight, the base is usually the first thing people want to cut, because nobody sees it once the concrete is down. I won't skimp on the subgrade, the ground the slab sits on, since a floor poured over raked dirt instead of dug-out, packed ground settles with that dirt, and no surface finish fixes that later.
Here's how it goes from the first call to the day we clean up, and who you'll be dealing with along the way.
When you call or send a message, I'm the one who comes out to look at the site, listen to what the floor is for and answer your questions. I've run this business in Calabasas since 2020, and the estimate I write up after that visit lays out the work and your price.
Whether a floor needs a permit is up to the city or county, not us, so we check with the office that covers your address before we start. We work through whatever they ask for with you, then get the ground and forms ready.
We're fully licensed and insured. I'm on the job with our crew from the pour through the cleanup, so the person who wrote your estimate is the one watching the work.
Before we pour, I'll tell you plainly that a new floor can show a few hairline cracks and that the slab has to dry before any flooring goes over it, because I'd rather you hear that from me now than find out on your own later. Then we go over what's going inside the slab, whether that's rebar, the steel bars that hold a slab together and add strength, welded wire mesh, which adds strength too, or fibers mixed into the concrete, which help with cracking but don't count as structural reinforcement. All three help keep cracks narrow, so the choice comes down to what the floor has to carry, and you'll know which one is in yours. We offer satisfaction guaranteed on every job, and to me that starts with you knowing what to expect from the slab.
A new floor often opens onto the yard, so we can pour concrete steps down from the new doorway at the same time. If the room looks out on the pool, our crew builds concrete pool decks too, and planning both slabs together keeps the heights and the water runoff working with each other.
Most of a good floor is decided before the concrete truck shows up. This is the order we work in.
We dig down to firm ground and pack it, and we check which way water runs so it drains away from the house instead of collecting under the floor. Getting this right is what keeps the slab from sinking in spots later.
We set the forms, place the reinforcement and leave any plumbing or electrical lines under the floor open where they can be seen. Nothing gets covered until the city's inspection is done, which we explain below.
We schedule the pour away from midday heat when we can, because concrete that sets too fast can end up with a weak, dusty top. Indoors we finish the surface smooth for flooring instead of giving it a broom finish, the rough texture we put on outdoor slabs for grip.
We saw control joints, shallow cuts that give the slab a planned place to crack, then let it cure, the wait while concrete gains strength, before anyone works on it. After that the slab still has to dry out before your flooring goes on.
Tell us the floor's size, what the room will be used for and what flooring you plan to put on top, and we'll reply within one business day. I'll set a time to come out, look at the site and write up a free estimate at your property, with no pressure to book.
(747) 269-3817Probably a little, because even a well-designed, well-built floor won't be completely free of cracks or curling, where the slab edges lift slightly, and some of both is normal on every project. What we control is where cracks form and how wide they get, with control joints usually sawn within 4 to 12 hours of the pour, depending on temperature and the mix, and the reinforcement we pick with you.
Calabasas requires a permit for all new construction, so ask the city's Building and Safety Division about your floor before work starts. Replacing flooring is on the city's list of minor projects that need no permit, and you can email the division at BuildingSafetyInfo@cityofcalabasas.com with questions about your project.
In California, most construction work has to be done by a licensed contractor, and the state's concrete contractor classification covers flat concrete work like floors. Calabasas says a property owner can sometimes get a permit as an owner-builder under strict limits, and a business owner or tenant doesn't qualify. The state's minor work exemption only covers jobs up to $1,000 that need no permit, done by someone who employs no one.
Not until the moisture inside the slab drops to an acceptable level, which one moisture meter maker says has to happen before any coating or flooring goes on. Trapped moisture can cause discoloration, buckling, blistering, glue that lets go or mold, so plan a gap between the pour and your finished floor.
In Calabasas, the building inspector generally checks permitted work before it gets covered, and the usual inspections include the foundation, the slab and any plumbing or electrical running underground. So anything under your floor stays open until that visit, and we pour after it, not before. If the inspector has to come inside a home you're living in, an adult over 18 has to be there, and the city recommends the contractor in charge come too so any problem gets talked through on the spot.
We're based in Calabasas and pour floors across the cities around it, including Thousand Oaks, Simi Valley, Agoura Hills, Oak Park and Westlake Village, along with Camarillo, Moorpark, Malibu, Topanga, Burbank and Santa Monica. A lot of what we see is additions, garage conversions and older houses getting a room built out, and if your city isn't on our list, call and ask.
Call (747) 269-3817 or use the form, since changing the floor plan before the pour is a lot easier than changing a slab after it.
If you're still deciding whether a concrete floor is right for the room, send me your questions and I'll walk you through it.
Tell us about your project